ZebraCardErrors Fields

Barcode: Reader initialization error

Barcode: Invalid/incomplete data read

Barcode: No data read

CFG: Copy active configuration to backup error

CFG: Copy active configuration to configuration copy error

CFG: Copy active configuration to factory error

CFG: Copy backup configuration to active configuration error

CFG: Copy configuration copy to active configuration error

CFG: Parse DOM error

CFG: Read active configuration error

CFG: Read backup configuration error

CFG: Reader configuration copy error

CFG: Read configuration defaults error

CFG: Read configuration into DOM error

CFG: Version mismatch

CFG: Write from DOM error

CNTR: Copy active counters to backup

CNTR: Copy backup counters to active counters

CNTR: Parse DOM error

CNTR: Read file error

CNTR: Read into DOM error

CNTR: Write from DOM error

Contact: Encoding timeout error

Contact: Read error

Contact: Write verification error

Contactless: Checksum error

Contactless: Flash read error

Contactless: Flash write error

Contactless: Invalid region code

Contactless: No reader installed

Contactless: Read error

Contactless: RF configuration error

Contactless: Unknown module error

Contactless: Write verification error

Donor: Ribbon calibration sensor error

Donor: Invalid ribbon

Donor: Invalid ribbon MAC

Donor: Out of ribbon

Donor: Ribbon ADC error

Donor: Ribbon BEMF error

Donor: Ribbon calibration error

Donor: Ribbon color detection error

Donor: Ribbon jam

Donor: Low ribbon

Donor: Ribbon motion error

Donor: Ribbon calibration sensor error

Donor: Ribbon calibration sensor error

Donor: Ribbon calibration sensor error

Donor: Ribbon calibration sensor error

Donor: Ribbon calibration sensor error

Engine: ATM card jam

Engine: Card cleaning error

Engine: Card eject error

Engine: Card feed error

Engine: Print path card jam

Engine: Card reject error

Engine: Card transfer error

Engine: Cleaning due error

Engine: Cleaning pre-warning error

Engine: Cleaning required error

Engine: Door open

Engine: EP script content error

Engine: EP script processing error

Engine: EP script transmission error

Engine: Feeder door open

Engine: Flipper card jam

Engine: Flipper initialization error

Engine: Flipper move failure

Engine: Flipper initialization error

Engine: Print path initialization error

Engine: Invalid EP script

Engine: Magnetic encoder card jam

Engine: Mag retrace error

Engine: Media drawer open

Engine: Motor voltage range error

Engine: Options module card jam

Engine: Options module initialization error

Engine: Print entrance card jam

Engine: Print exit card jam

Engine: Print path card jam

Engine: Print path initialization error

Engine: Print synchroniztion card jam

Engine: Printhead cable disconnected

Engine: Printhead CAM home error

Engine: Printhead initialization error

Engine: Printhead temperature too high

Engine: Printhead temperature too low

Engine: Protocol error

Engine: Pusher plate error

Engine: Reject bin full

Engine: Smartcard CAM error

Engine: Smartcard initialization error

Engine: Smartcard positioning error

Engine: Transfer rollers temperature too high

Engine: transfer rollers temperature too low

Ethernet: Open failed

HCB: Bootloader mode - Firmware reload may be required

HCB: Bulb error

HCB: Control board missing

HCB: Sensor error

Imaging: Drawing render error

Imaging: Font render error

Imaging: Image processing aborted

Imaging: Image to print area error

Imaging: Received incomplete image data

Imaging: Invalid image bits per pixel format

Imaging: Invalid image processing data

Imaging: Error sending IPD to job scheduler

Imaging: Print to media area error

Imaging: Error receiving IPD

Job: Job aborted

Job: Job buffer full

Job: Job cancelled

Job: Create job error

Job: EP Processing error

Job: Job ID not found

Job: Insufficient memory available to accept job

Job: Queue error

Laminator: Bootloader mode - Firmware reload may be required

Laminator: Bottom cutter failure - Power off printer and correct problem

Laminator: Bottom cutter stall - Power off printer and correct problem

Laminator: Bottom heater error - Power off printer and correct problem

Laminator: Bottom heater over temperature - Power off printer and correct problem

Laminator: Bottom laminate feed error

Laminator: Bottom laminate registration error

Laminator: Bottom sensor failure - Power off printer and correct problem

Laminator: Door open

Laminator: Early card jam

Laminator: EEPROM corrupt

Laminator: Fan failure - Power off printer and correct problem

Laminator: Initialization error

Laminator: Initializing

Laminator: Invalid bottom laminate

Laminator: Invalid top laminate

Laminator: Late card jam

Laminator: MAB Bootloader mode - Firmware reload may be required

Laminator: Media authentication board missing

Laminator: Mid card jam

Laminator: Missing laminator

Laminator: Out of bottom laminate

Laminator: Out of top and bottom laminate

Lamintaor: Out of top laminate

Laminator: Poll timeout

Laminator: Remove top and bottom laminate

Laminator: Remove bottom laminate

Laminator: Remove top laminate

Laminator: Staging error

Laminator: Top cutter failure - Power off printer and correct problem

Laminator: Top cutter stall - Power off printer and correct problem

Laminator: Top heater error - Power off printer and correct problem

Laminator: Top heater over temperature - Power off printer and correct problem

Lamintaor: Top laminate feed error

Laminator: Top laminate registration error

Laminator: Top sensor failure - Power off printer and correct problem

Laminator: Unknown error

MAB: Bootloader mode - Firmware reload may be required

MAB: Control board missing

Mag: No data read

Mag: No magnetic stripe detected

Mag: Read error

Mag: Receive error

Mag: Write verification error

MCU: Feeder control board in boot loader mode

MCU: Feeder control board communication error

MCU: Feeder control board firmware upgrade error

MCU: Feeder missing

MCU: Flipper control board in boot loader mode

MCU: Flipper control board communication error

MCU: Flipper control board firmware upgrade error

MCU: Flipper missing

MCU: Options control board failure

MCU: Options control board in boot loader mode

MCU: Options control board communication error

MCU: Options control board firmware upgrade error

MCU: Options missing

MCU: Sensor control board in boot loader mode

MCU: Sensor communication error

MCU: Sensor control board firmware upgrade error

MCU: Sensor missing

Media: Card feeder is empty

Media: Card jam

Media: Card not detected

Media: Insert card timeout

Media: Invalid card type

Media: Invalid retransfer media

Media: Invalid retransfer media MAC

Media: Out of cards

Media: Out of retransfer media

Media: Retransfer media jam

Media: Retransfer media motion error

Memory: Data delete error

Memory: Data store error

Memory: Erase EP failure

Memory: Erase FPGA failure

Memory: Erase IP failure

Memory: File access permission error

Memory: File delete error

Memory: Invalid file path

Memory: File read error

Memory: File write error

Memory: Font delete error

Memory: Font store error

Memory: Pool allocation error

Memory: Pool de-allocation error

Memory: NVM access error

Memory: NVM backup error

Memory: NVM CRC error

Memory: NVM EP communication error

Memory: NVM erase backup error

Memory: NVM initialization error

Memory: NVM open or close error

Memory: NVM program backup error

Memory: NVM restore error

Memory: Out of external flash

Memory: Out of internal flash

Memory: Out of NVM

Memory: Out of RAM

Memory: Program EP failure

Memory: Program FPGA error

Memory: Program IP failure

OCP: Transmit error

OCP: Unresponsive

SDK: Barcode reader is not available

SDK: Buffer overflow

SDK: Device already open

SDK: Device in session with another host

SDK: Device not available

SDK: Device not open

SDK: Device not responding

SDK: Disconnect error

SDK: Encryption error

SDK: Insufficient data received from device

SDK: Invalid argument

SDK: Bad ZMC command echo

SDK: Invalid ZMC response signature

SDK: Empty/Invalid Data structure

SDK: Invalid device for requested operation

SDK: Invalid media for requested operation

SDK: Requested operation not supported

SDK: Dual sided printing not supported

SDK: Job status error

SDK: Memory allocation error

SDK: Unable to obtain exclusive access to device

SDK: No devices found

SDK: Requested operation timed out

SDK: Passphrase or security key required for requested operation

SDK: Smartcard encoder not available

SDK: Unexpected error

SDK: Wi-Fi not available

SDK: Write data error

SDK: Path to XML element not found

SDK: XML parse error

Security: Authentication failed

Security: Create random error

Security: Read random error

Security: Read serial number error

Security: Invalid crypto key

Security: Invalid HMAC

Security: Invalid passkey

Security: Invalid printer data

Security: Unsupported action

STACKER: Communication error

STACKER: Deck full

STACKER: Entry jam

STACKER: Hopper absent

STACKER: Hopper full

STACKER: Initialization error

STACKER: Invalid firmware

STACKER: Lift jam

STACKER: Module missing

STACKER: Unauthorized module

System: MLB authentication error

System: Boot region integrity error

System: Critical error

System: Duplex upgrade error

System: EP diagnostic mode error

System: Firmware upgrade failed

System: Incompatible firmware upgrade attempted

System: Intertask message error

System: Invalid hardware configuration error

System: No error

System: Printer powering up

System: Program region integrity error

System: Watchdog timer error

USB: Handle error

USB: Locked

USB: Message error

USB: Open failed

USB: Payload pending

USB: Payload too big

USB: Restart

USB: Message short

USB: Synchronization error

WIFI: Access point missing

WIFI: Association failed

WIFI: Connection failed

WIFI: Incompatible configuration

WIFI: Link lost

WIFI: Open failed

ZMC: Cancel Action error

ZMC: Command processing error

ZMC: Communication synch error

ZMC: Data less than specified in header

ZMC: Data more than specified in header

ZMC: Device reservation failed

ZMC: Start Action already called

ZMC: End Action error

ZMC: HMAC missing

ZMC: Invalid command

ZMC: Invalid parameter (1)

ZMC: Invalid parameter (2)

ZMC: Invalid parameter (3)

ZMC: Invalid payload content

ZMC: Invalid payload length

ZMC: Invalid sub-command

ZMC: Job data error

ZMC: Memory-pool allocation error

ZMC: No Start Action

ZMC: Parameter not found

ZMC: Parameter value outside of valid range

ZMC: Parameter setting error

ZMC: Incorrect parameter type

ZMC: Printer busy

ZMC: Printer offline

ZMC: Host write occurred when host read expected

ZMC: Response too large for host

ZMC: Host read occurred when host write expected

ZMC: XML parse error

ZMJ: No barcode reader installed

ZMJ: Command processing error

ZMJ: Number of requested copies out-of-range

ZMJ: Data decryption error

ZMJ: Invalid command

ZMJ: Invalid job ID

ZMJ: Invalid ZMOTIF version

ZMJ: Job already open

ZMJ: Job Control XML parse error

ZMJ: No magnetic encoder installed

ZMJ: Command identifier 'ZBR1' not found

ZMJ: No XML data received

ZMJ: No job type received

ZMJ: No matching encoder type

ZMJ: Unknown job type received